What Sizes Are An Fittings

This is known as AN Thread Size. This will cause leaks and damage to the fittings.

Sae Thread Jic Fitting Size Chart Size Chart Chart Fittings

1 34 2 332.

What sizes are an fittings. In these examples the fractional parts or 58 represent the given hoses internal dimensions in inches. Aside from thread sizes the most important difference between AN and NPT threaded fasteners is that NPT uses a tapered threadMetal threads should be treated with a sealant paste aka pipe dope. Understanding AN fittings All AN fittings have a mating flare seat at 37 degrees This guide will use the AN name to refer to these fittings.

This specification dictates angle threading and the inside and outside diameters of hose the fittings are used in conjunction with. The 115 of course relates to the thread pitch that we explained above. - AN and ORB thread are the same diameter.

In bolts the number refers to the diameter of the bolt whereas in a fitting it refers to the OD of the tube and thereby have different threads. The standard hose fitting size is either -115 NH or 58-115 NH. AN fittings use a 37 degree flare as the sealing surface.

14 Zeilen AN Standards as Applied to Fluid Carrying Fittings Each AN size also references a standard male and female thread size that is used on fittings - such as hose end fittings adapters and port fittings. On the other hand AN fittings are flare-type compression fittings and as. 1 18 1 716-24.

Dash Numbers are typically assigned based on the size. Each AN size refers to the outer diameter od of the tube or inner diameter id of the hose that its used with. Gasket Fitting Sizes AN Fitting Sizes Pipe Thread Fitting Sizes NPT Fitting Sizes Hose End Sizes.

Each AN size also has its own standard thread size. The number represents the OD as multiples of 116. DO NOT use AN fittings with different flare-type fittings.

1 12 1 1316-32. AN fittings are produced with a variety of different angles to assist with routing and clearance they come in straight 30 45 60 90 120 150 and even 180 degrees. 1 38 1 4564-28.

Download Fitting Identification Charts PDF. You can also see this post to learn just about everything else about garden hoses. -4 AN 416 or 14.

This system does not specify the inside diameter of the tubing because the tube wall can vary in thickness. 15 Zeilen Hose Size Chart Fractional Equivalent All dimensions are in inches unless otherwise noted. AN HEX OD IDENTIFICATION CHART.

AN fittings come in a variety of standardized sizes based on a long-standing military specification. For example AN6 bolt has a 38 -24 thread whereas an AN6 fitting has a 916 -18 thread. Since tubing and hoses have assorted wall thicknesses depending on manufacturers the designated size number does not necessarily tell us anything about the inside diameter ID of the plumbing component.

If you are unsure as to what size fitting you have lay your fitting over the appropriate drawing to determine its size. Aluminum Fitting Sizes Aeroquip Fitting Sizes Earls Fitting Sizes XRP Fitting Sizes Fragola Fitting Sizes Russell Fitting Sizes A-1 Performance Plumbing Fitting Sizes Jiffy-Tite Fitting Sizes Mr. The line drawings below depict the actual sizes of the various common ANORB thread sizes.

Some fittings even come with special ports for pressure or temperature sensors. AN seals with the flare ORB seals with an O-ring. Since tubing and hoses can have different wall thicknesses the size number does not.

Use this handy chart to determine the -AN fitting size based on corresponding thread sizes. Thread Size Chart for AN Fittings. You can convert any AN fitting to its nominal inch size by dividing the AN number by 16 as follows.

AN Army-Navy sizes were established by the Aerospace industry years ago. The number represents the OD Outside Diameter of the tube the fitting was designed to fit in the old AN specifications. Note that 37 AN and 45 SAE fittings and tooling are not interchangeable due to the different flaring angles.

The numbers assigned equal the size in 116 inch increments. The O-ring size is typically defined by the AS standard. Tee fittings can be used for coolant where there are multiple lines.

AN sizes range from -2 to -32 in irregular steps with each step equating to the OD outside diameter of the tubing in 116 increments. The numbers are equal to the outside diameter OD of the tubing in 116. If you cant find an AN fitting for your application find a local hydraulic shop and use simple SAE fittings.

AN fittings come in a range of sizes they are called the dash size because it has a dash followed by two digits. They may not be red or blue buy theyll fit just fine. Here is an AN size chart.

AN fittings have Straight Thread and use O-ring seals. AN sizes are shown as a size number prefixed with a hyphen so a -10 fitting would be called a Dash 10 AN fitting.

Jis Vs Bsp Fitting Dimensions Difference Table I2 I3 British Standards Fittings Zhejiang

Pin On General Information

Jic Fitting End Hex Wrench Size Chart Knowledge Yuyao Jiayuan Hydraulic Fitting Factory Wrench Sizes Hex Wrench Size Chart

Pin On Products

Jic Flare Fittings Sizes Words Steel Sheet Music

Jis 30 Deg Flare Fitting Metric Thread Komatsu Style Dimensions Metric Thread Chart Metric Thread Hydraulic

Pin On Ham Radio

Sae J2494 1 2 3 4 Push To Connect Fittings Standards Sae Connection Traffic Safety

Pin En Log Burner Chimnear

Jis Vs Bsp Fittings Sizes Drawings Difference Fittings Floor Plans British Standards

Sae J2552 Female Swivel Jic 37 Flared Push On Hose Fittings Sae J846 2401a8 Dimension Swivel Sae Flared

Sae J514 Hex Tolerance For Jic Fitting Size Chart Wrench Sizes Hex Wrench Size Chart

Jic Fitting Size Drawing Chart Sae J514 Chart Fittings Drawings

Pin On Dimensions

Pin On Hose Fittings Information

Sae Thread Orb Fitting Size Chart Size Chart Orb Size

Pin By Ray On Jic Jis Bsp Din Iso Sae Hydraulic Fittings Drawing Size Chart Size Chart Symbols

Pin En All Terrain

Jic Fitting Wrench Hex Size Chart Wrench Sizes Size Chart Wrench